summaryrefslogtreecommitdiff
path: root/ubi-utils/scripts
AgeCommit message (Collapse)Author
2008-01-15ubi-utils: bin2nand, nand2bin add support of different ecc layoutsFrank Haverkamp
Both tools were lacking support of alternate ECC layouts. Only our intitial format was supported. With this change, it should be very easy to add more layouts in addtion to the already supported ones, which are: IBM (our format), and the MTD default layout. NAND OOB sizes of 512 and 2048 are currently supported. In contrast to the old version of bin2nand, the holes inbetween the ECC data is now not filled with 0x00 anymore but instead 0xff (like deleted flash) is used. This should not cause any difference. The testcase reflects the different layouts too. Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2007-12-23ubi-utils: move ubi_jffs2_test.sh to better placeArtem Bityutskiy
... to tests/ubi-tests/ Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2007-12-23ubi-utils: move jffs2_test.shArtem Bityutskiy
Move this piece of code to sort-me-out/. See README. Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2007-12-15ubi-utils: add more TODOsArtem Bityutskiy
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2007-12-15ubi-utils: add a TODOArtem Bityutskiy
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2007-11-24ubi-utils: nand2bin had ECC calculation problemsFrank Haverkamp
Fixed a problem when ECC was checked. The correction was not properly done by subpage. Added more output for the moment to be able to figure out more potential problems. Added testcase: bin2nand2bin.sh and biterror inject program inject_biterror.pl Interface o ECC correction disabled by default. Switch to turn it explicitly on. The user must specify what he wants to be done. Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2007-11-24ubi-utils: various fixes in unubiFrank Haverkamp
The extraction of data from blocks used for dynamic volumes was totally broken. The data size was calculated wrong. This fix is not perfect, the alignment is still ignored. The parameter "header-size" is very misleading. It does not reflect the vid hdr offset properly. I assume therefor that it only works for the layout I am using where the vid hdr is at the _end_ of the 1st NAND page (2048). I added the generation of a textfile with information about the blocks which are going into the internal graph representation. Instead of a graph I think that a simple array will simplify the code very much. The array must than be sorted properly to cope with older and newer block-copies but that should not be a problem. discussed the tool with my coleage Andreas Arnez and we found that it might be a good idea to replace it even with a perl program for the same purpose since that would offer the flexibility to change it on the fly when needed. The tool is mainly used for crash analysis so it could be an advantage to change it without needing a C-compiler. Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2007-11-24ubi-utils: Test-case for unubiFrank Haverkamp
We have no good testcases for this kind of tool yet. Adding a 1st draft. Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2007-06-18UBI: fix testsArtem Bityutskiy
This patch fixes UBI tests and adds udev problems solution description. Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2007-03-29UBI-Utils: Add a run_all.sh scriptAdrian Hunter
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
2007-03-29UBI-Utils: Updated scripts for latest UBIAdrian Hunter
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
2006-12-20[MTD] UBI Utils: Update testscriptsFrank Haverkamp
2006-11-06[MTD] UBI: Update testscriptsFrank Haverkamp
The testscripts ensure the correct functionality of the UBI code on my reference system. Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2006-10-31[MTD] UBI: Enhanced example for testing.Frank Haverkamp
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2006-10-31[MTD] UBI: Removed automake, autoconf, added ubi userspace headers.Frank Haverkamp
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
2006-10-31UBI - Unsorted Block ImagesFrank Haverkamp
UBI (Latin: "where?") manages multiple logical volumes on a single flash device, specifically supporting NAND flash devices. UBI provides a flexible partitioning concept which still allows for wear-levelling across the whole flash device. In a sense, UBI may be compared to the Logical Volume Manager (LVM). Whereas LVM maps logical sector numbers to physical HDD sector numbers, UBI maps logical eraseblocks to physical eraseblocks. More information may be found in the UBI design documentation: ubidesign.pdf. Which can be found here: http://www.linux-mtd.infradead.org/doc/ubi.html Partitioning/Re-partitioning An UBI volume occupies a certain number of erase blocks. This is limited by a configured maximum volume size, which could also be viewed as the partition size. Each individual UBI volume's size can be changed independently of the other UBI volumes, provided that the sum of all volume sizes doesn't exceed a certain limit. UBI supports dynamic volumes and static volumes. Static volumes are read-only and their contents are protected by CRC check sums. Bad eraseblocks handling UBI transparently handles bad eraseblocks. When a physical eraseblock becomes bad, it is substituted by a good physical eraseblock, and the user does not even notice this. Scrubbing On a NAND flash bit flips can occur on any write operation, sometimes also on read. If bit flips persist on the device, at first they can still be corrected by ECC, but once they accumulate, correction will become impossible. Thus it is best to actively scrub the affected eraseblock, by first copying it to a free eraseblock and then erasing the original. The UBI layer performs this type of scrubbing under the covers, transparently to the UBI volume users. Erase Counts UBI maintains an erase count header per eraseblock. This frees higher-level layers (like file systems) from doing this and allows for centralized erase count management instead. The erase counts are used by the wear-levelling algorithm in the UBI layer. The algorithm itself is exchangeable. Booting from NAND For booting directly from NAND flash the hardware must at least be capable of fetching and executing a small portion of the NAND flash. Some NAND flash controllers have this kind of support. They usually limit the window to a few kilobytes in erase block 0. This "initial program loader" (IPL) must then contain sufficient logic to load and execute the next boot phase. Due to bad eraseblocks, which may be randomly scattered over the flash device, it is problematic to store the "secondary program loader" (SPL) statically. Also, due to bit-flips it may become corrupted over time. UBI allows to solve this problem gracefully by storing the SPL in a small static UBI volume. UBI volumes vs. static partitions UBI volumes are still very similar to static MTD partitions: * both consist of eraseblocks (logical eraseblocks in case of UBI volumes, and physical eraseblocks in case of static partitions; * both support three basic operations - read, write, erase. But UBI volumes have the following advantages over traditional static MTD partitions: * there are no eraseblock wear-leveling constraints in case of UBI volumes, so the user should not care about this; * there are no bit-flips and bad eraseblocks in case of UBI volumes. So, UBI volumes may be considered as flash devices with relaxed restrictions. Where can it be found? Documentation, kernel code and applications can be found in the MTD gits. What are the applications for? The applications help to create binary flash images for two purposes: pfi files (partial flash images) for in-system update of UBI volumes, and plain binary images, with or without OOB data in case of NAND, for a manufacturing step. Furthermore some tools are/and will be created that allow flash content analysis after a system has crashed. Who did UBI? The original ideas, where UBI is based on, were developed by Andreas Arnez, Frank Haverkamp and Thomas Gleixner. Josh W. Boyer and some others were involved too. The implementation of the kernel layer was done by Artem B. Bityutskiy. The user-space applications and tools were written by Oliver Lohmann with contributions from Frank Haverkamp, Andreas Arnez, and Artem. Joern Engel contributed a patch which modifies JFFS2 so that it can be run on a UBI volume. Thomas Gleixner did modifications to the NAND layer and also some to JFFS2 to make it work. Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>