| Age | Commit message (Collapse) | Author |
|---|
|
Forbid the use of less than 2 eraseblocks in nandpagetest. It is obvious
that the test cannot run on zero block, but it cannot run on only one
block neither. The reason is: get_first_and_last_block() will return the
same id for both the first and the last blocks. In erasecrosstest(),
the logic is:
- erase/write/read/verify first block
- erase/write again first block
- erase *last* block
- read/verify first block
When using only one block, 'first' refers to the same block as 'last',
leading to erasing the block before reading it. Hence, the test would
fail with no actual reason.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Bit flip detection for written and erased pages tend to have different
implementations. Where written pages are detected and corrected using
ECC, erased pages are typically detected by ensuring that the number of
zeros is less than a specified threshold.
As such, it's necessary to have the 'nandbiterrs' test support the
testing of written and erased pages. Bit flips in erased pages are
emulated by rewriting the page in raw mode, to prevent the use of ECC.
Signed-off-by: Harpreet Eli Sangha <harpreet@nestlabs.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
After a page read, the old failure statistics are compared against the
new failure statistics before the new values are actually read.
Signed-off-by: Harpreet "Eli" Sangha <harpreet@nestlabs.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
On 32bit systems (e.g. ARM) the size of off_t can be 4 byte and the size of loff_t 8 byte.
This causes compiler warnings like the following:
flash_erase.c: In function 'show_progress':
flash_erase.c:56:22: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'off_t {aka long int}' [-Wformat=]
bareverbose(!quiet, "\rErasing %d Kibyte @ %"PRIxoff_t" -- %2i %% complete ",
and an output like this:
~# flash_erase /dev/mtd2 0 1
Erasing 64 Kibyte @ 6400000000 -- 0 % complete
~#
Since the size of off_t and loff_t can differ from each other, the
printf format specifier should be determined separately for both.
Further the format specifiers should be based directly on the size of the
particular data type.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Basically a user space port of the mtd sub page test kernel module.
In addition to the module parameters, the utility supports using
only a sub-range of the flash erase blocks with a configurable
stride and can restore the block contents after the test.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Basically a user space port of the mtd page test kernel module.
In addition to the module parameters, the utility supports using
only a sub-range of the flash erase blocks with a configurable stride.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Basically a user space port of the mtd read test kernel module.
In addition to the module parameters, the utility can scan only
a sub-range of the flash erase block with a configurable stride.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Basically a user space port of the mtd speed test kernel module.
In addition to the module parameters, the utility can resture
the block contents after test and allows setting the maxium writes
for the test.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Basically a user space port of the mtd speed test kernel module.
In addition to the block offset and count module parameters, the
utility supports a block stride and can restore the block contents
after test. Furthermore, a flag can be used to disable destructive
tests (i.e. only perform read speed tests).
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Basically a user space port of the mtd stress test kernel module.
In addition to the block offset and count module parameters, the
utility supports a block stride and can restore the block contents
after test.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Basically a user space port of the mtd torture test kernel module. In
addition to the block offset and count module parameters, the utility
supports a block stride and can restore the block contents after test.
In contrast to the kernel module, the torture test is implemented by
the libmtd mtd_toruture function and thus doesn't allow for similarly
fine grained options on diagnostics.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
