| Age | Commit message (Collapse) | Author |
|---|
|
When writing a full 4GiB NAND to a file end_addr becomes 0x100000000.
With that writing out the first page to the file doesn't happen
because size_left is calculated to 0x100000000 - 0 = 0x100000000
which is then truncated to 32bit and becomes zero. Fix this by
using an appropriate 64bit type for size_left.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Such blocks may be incorrectly treated as empty (even though they may
have non-erase OOB). Warn about it so people may start useing
--skip-all-ffs .
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Using == with `test` is a bashism. POSIX shell only supports =.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
In commit a888044525, various header files that were added to the
distribution tarball via EXTRA_DIST were instead added to the source
lists of their respective programs instead.
In the case of jffsX-utils, a missing escape for a new-line in the
source list caused the include/linux/jffs2.h header to not be packged
in the release tarball. This went undiscovered, as the system on which
the release tarball was built, had the same header installed installed
in the system include directory, so a `make distcheck` succeeded.
Fixes: a888044525
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
misc-utils/fectest.c:37:11: warning: iteration 47 invokes undefined behavior [-Waggressive-loop-optimizations]
37 | srcs[i] = buf + (i * PKT_SIZE);
| ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Same fix as a2c6bbc ("mtd-tests: Read and write pages during speed
tests") but applied to flash_readtest and flash_stress.
Resolves failure of flash_readtest when subpages are present. The test
reads a (sub)page followed by the entire OOB. Upon reaching the 2nd
subpage, the OOB read fails because it is beyond the end of OOB.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The speed test does reads and writes of different sizes:
- eraseblock
- page
- two pages
At least this is the theory because, as opposed to the legacy kernel
module doing the same measurement, the userspace tool uses the subpage
size (hence accessing the same page 4, 8 or 16 times depending on the
subpage setting). Of course if the controller does not support subpages,
this issue is not visible.
Use mtd.min_io_size instead for non-NOR devices in order to get the
right bandwidth (at least one that fits the logs).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
ubiscan will scan the PEBs in a specific MTD device and print a summary of
the PEB erase counters and (optionally) details about each PEB's status.
Example output:
# ./ubiscan /dev/mtd6
Summary
=========================================================
mtd : 6
type : nand
size : 110362624 bytes (105.2 MiB)
PEBs : 842
min I/O: 2048 bytes
PEB erase counters
=========================================================
valid : 834
empty : 0
corrupted: 0
alien : 0
bad : 8
Histogram
=========================================================
from to count min avg max
---------------------------------------------------------
0 .. 9: 55 1 4 9
10 .. 99: 174 10 48 99
100 .. 999: 514 103 287 987
1000 .. 9999: 91 1004 1880 2251
10000 .. 99999: 0 0 0 0
100000 .. inf: 0 0 0 0
---------------------------------------------------------
Total : 834 1 392 2251
If the --verbose switch is given, ubiscan will print PEB details:
# ./ubiscan --verbose /dev/mtd6
[... same output as before ...]
Details
=========================================================
PEB 0: 253
PEB 1: 1489
PEB 2: 1
PEB 3: 1
PEB 4: 1
PEB 5: 1
PEB 6: 1
PEB 7: 1
PEB 8: 1
PEB 9: 1
PEB 10: 1
...
PEB 832: 1225
PEB 833: 252
PEB 834: 111
PEB 835: 298
PEB 836: 1264
PEB 837: 11
PEB 838: EB_BAD
PEB 839: EB_BAD
PEB 840: EB_BAD
PEB 841: EB_BAD
Signed-off-by: Diego Ismirlian <dismirlian@gmail.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
- The original flashcp process is erase, write and verify all blocks
in one time from file to device.
This patch will add a function that only copy different block data
from file to device. The function will compare blocks by block
between file and device, then erase and write block data from file
to device if found different block.
Signed-off-by: Harvey Wu <harveywu95@gmail.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
On some SPI NOR flashes you can actually erase the OTP region until its
fully locked. Add a small utility for that.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Some flash types support full erase chip command which can reduce the
flash erase time. Try first to erase the entire flash and fall back
to the old method if the operation fails.
Signed-off-by: Larisa Ileana Grigore <larisa.grigore@nxp.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Running mkfs.ubifs which was build without crypto triggered the
following assertion:
mkfs.ubifs: ubifs-utils/mkfs.ubifs/fscrypt.h:166:
inherit_fscrypt_context: Assertion `0' failed.
A previous commit-cc4c5e295f54 ("mkfs.ubifs: Enable support for building
without crypto") added a check for an existing fscrypt context before calling
functions inherit_fscrypt_context() and free_fscrypt_context(),
however did not properly do this for each call to these functions.
Fixes: cc4c5e295f54 ("mkfs.ubifs: Enable support for building without crypto")
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Currently mtd-utils on 32bit systems fail on devices >2GiB due to off_t being
a signed 32bit type. Add AC_SYS_LARGEFILE to make off_t a 64bit type.
Adding AC_SYS_LARGEFILE results in _FILE_OFFSET_BITS being defined to 64
in include/config.h. To let this have an effect we must make sure that
include/config.h is included before all other includes which is
archieved by adding its inclusion to CPPFLAGS.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
- Remove "install tests" configure option, we already have an option
whether to build tests or not. Don't try to work around autotools
semantics that people building the package expect.
- Fix the installation path by propperly defining it and using the
correct name for the libexec path.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Throughout the Automake files, there is a consistent pattern somewhat
like this:
FOO_BINS = ....
sbin_PROGRAMS += $(FOO_BINS)
This commit all such patterns whenever the variable is not used anywhere
else and appends to the target directly.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
This commit removes the C header files from the EXTRA_DIST variables
and instead assigns them to the SOURCE variable of the respective
components they belong to.
This takes care of having them distributed in the release tar ball and
helps with dependency tracking a little.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The concept of erase blocks doesn't apply to mtd-ram devices. Such
devices set MTD_NO_ERASE to indicate this and some report 0 for the
erase block size. Avoid a divide by zero when calculating the erase
block count for such devices.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The "need_getrandom" check and result is used only for the "ubihealthd".
This tool is very important to have it around at run-time, while the
corresponding "mkfs.ubifs" tool is still optional (think about offline
generated ubifs images).
Since compiling "mkfs.ubifs" adds more dependencies (various shared
libraries), buildsystems for embedded devices will add these shared
libraries to the root filesystem even if "mkfs.ubifs" isn't used or
installed.
Thus, handling both tools independently makes sense. The previous behavior
is kept, e.g. if UBIFS support is enabled, it enables "ubihealthd" as well.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
This abstracts away attaching of the right ubi and then selecting the right
ubi device and volume to mount.
As described in the comment at the top this allows to mount ubifs volumes
directly from /etc/fstab without having to use hardcoded numbers (which
depend on mount order and so are unreliable) and extra magic to care for
attaching.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Especially for the pkcs11 engine, a configuration is required
because the provider has to be configured.
Its not clear why OPENSSL_no_config() is called.
Remove OPENSSL_no_config() and call OPENSSL_config(NULL)
instead.
Signed-off-by: Torben Hohn <torben.hohn@linutronix.de>
Signed-off-by: Bastian Germann <bage@linutronix.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The nandflipbits tool is intended to be used when one need to flip one or
several specific bits on a NAND media.
It can be useful to manually recover from an unexpected bit flip on a flash
device, though the main purpose of this tool is to provide a way to test
ECC algorithms robustness.
One typical example I used this tool for is testing HW ECC engines behavior
when bitflips occur in an erased page: most HW engines do not correctly
handle this case, because, most of the time, ECC bits generated for an
empty page are not all 1s, and, empty page detection embedded in such
engines is only validating that all bits are set to 1s (which is not true
when a bit-flip has occurred).
Another use of this tool is replacing nandbiterrs test which
absolutely do not work with MLC-like chips because of the rewriting of
the pages in raw mode to toggle ones into zeroes.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
[miquel: Took Boris' work from 2014, addressed comments from Brian made
in 2015, updated it, tested more extensively and fixed issues]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
8f627247f6("mtd-utils: move libmtd source files to lib/ subdirectory")
removed fectest.c from the build system 10 years ago. Add it again.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
In v2.1.0, SELinux support was introduced. It never compiled with ubifs
because it uses the old add_xattr signature that also changed in v2.1.0
with a1bd316e23("mkfs.ubifs: Implement fscrypto context store as xattr").
Add the ubifs_ino_node and name to the call and remove the nm that is
contructed in the new function version.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
default paths
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The sign.h header added by the authentication patch set was omitted
from the automake file and thus not added to the distribution tarball.
The resulting tarballs were unable to be compiled.
Fixes: a739b59 ("mkfs.ubifs: Add authentication support")
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
First, there is no option named of X509_OPTION. It was presumably
changed during development to AUTH_CERT_OPTION. This commit fixes
the name in the !WITH_CRYPTO branch.
Similarly, '}' got moved into the WITH_CRYPTO branch, but not into
else branch, resulting in tons of errors if fscrypt is disabled.
This commit pulls it back out of both branches.
Fixes: a739b59e ("mkfs.ubifs: Add authentication support")
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
This commit fixes some uses of strncpy that could leave the destination
buffer unterminated.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The function reads file data into a buffer and then checks if we
actually are at the end-of-file by trying to read one more byte.
For whatever reason, the code uses an int instead of a char. It's
not pretty but works. But again, this is something that every
static analysis tool barks at.
Further more, the error messages are inverted. "We aren't at EOF yet"
is printed on failure and something like "read error %m" is printed
on success.
This patch fixes all of the above.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Some temporary buffers are allocated with "sizeof(pointer) * count" as
size argument, which cannot possibly be correct.
Assuming what was meant was "sizeof(pointer[0]) * count" makes sense
in the context of how the buffers are used, but is actually pretty
pointless, since the buffers are unsigend char.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
This patch modifies the internal helpers to read and parse integers
from sysfs files by initializing them first and removes turns an
obscure "a = open(...) if (a >= 0) {...} if (a == -1) {...}" inside
recv_image into a more straight forward if/else branch.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
This patch restructures various code parts that follow the pattern
of "stat(x, &sb) ... makes_sense(&sb) ... open(x)".
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Many tools open a file descriptor, close it a the end and have some
form of error path in between that jumps to the end.
In some cases, if opening the file fails the error path is taken and
the utility ends up closing one or more invalid file descriptors. It's
technically not a real issue but something that pretty much any static
analysis tool barks at.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
libubi.h includes ubi-media.h which was made private in the kernel a
long time ago. There are users of libubi.h, e.g. swupdate, which have to
have ubi-media.h available at build time with this inclusion.
However, libubi.h uses only one symbol from ubi-media.h. Define that symbol
in the header to enable using libubi.h without installing ubi-media.h.
Make up for the transitive symbol use in ubiformat.c by including ubi-media.h.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
libubigen.h does not use any symbol from mtd/ubi-media.h,
so remove it from includes.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
This changeset fixes a feature regression in ubiformat. Older versions of
ubiformat, when invoked with a flash-image, would return 0 in the case no error
was encountered. Upon upgrading to latest, it was discovered that ubiformat
returned 255 even without encountering an error condition.
This changeset corrects the above issue and causes ubiformat, when given an
image file, to return 0 when no errors are detected.
Tested by running through my loading scripts and verifying ubiformat returned
0.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
There are flashes which have gaps between OTP regions and flashes where
the regions don't start at 0 (for example the Winbond 25Q series, which
has three 256 bytes OTP regions starting at 0x1000, 0x2000 and 0x3000).
At the moment it is impossible to dump the OTP memory. Fix it by passing
an optional offset parameter.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The ubihealthd depends on sys/random.h , which is not present on some
older systems. Build ubihealthd only if sys/random.h is present.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The value 0 is a valid file descriptor. The existing error handling
would not only treat that as an error, but subsequently leak the
file descriptor in the error handling path.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The existing code had multiple error handling labels and did things
like checking if a buffer is not NULL before freeing it.
This patch collapses all of this into a single label. We can do this,
because the standard guarantees us that it is safe to call free() with
a NULL pointer.
This also has the side effect of removing the possibility of using the
wrong error label and accidentally leaking something.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
For some command line flags, the argument string is copied. Simply
writing over the buffer leads to a resource leak if the same flag
is specified on the command line more than once.
This patch adds a free() call to the old buffer before overwriting
it with the new copy.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
The original code had a 'goto out_close' directly after a return error
code, which is obviously not what was intended.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
|
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
|
